Case Study: International Fastener Manufacturer Saves Millions by Upgrading Its Existing Air Filtration System

Case Study International fastener MANUFACTURER saves millions by upgrading existing air filtration system.

Background

A leading manufacturer of cold-headed fasteners in the Cleveland area was experiencing serious indoor air quality issues throughout its facility. The plant relied primarily on an existing SmogHog® air filtration systems, but years of inadequate maintenance and system inefficiencies had significantly reduced its performance. Poor air quality raised concerns about employee health, productivity, equipment reliability, and long-term employee retention.

More than two years later, Bee Clean Specialties continues to provide scheduled preventive maintenance on the facility’s SmogHog® system. Bee Clean also provides inspection, maintenance, repair, and upgrade services for MistBuster®, Tri-Mist®, Trion®, Aerocology®, and Coolblaster® electrostatic air cleaners, helping manufacturers maximize equipment life and maintain excellent indoor air quality without unnecessary replacement costs.

The company knew improvements were necessary but was hesitant to replace the entire air filtration system. A sister facility with similar air quality issues had recently invested approximately $1.5 million in a completely new filtration system. Because this Cleveland facility operated significantly more cold heading machines, a comparable replacement was estimated to cost nearly $3 million.

The Challenge

After performing a complete system evaluation, Bee Clean Specialties identified several issues that were preventing the existing SmogHog® system from operating efficiently.

The primary problems included:

  • The electrostatic air cleaners had not been serviced on a regular maintenance schedule.
  • Much of the ductwork was improperly designed, undersized, and out of balance, restricting airflow throughout the system.
  • Several SmogHog® units were undersized for their applications and could not provide the CFM required to effectively capture smoke at the source.

These same issues are commonly found in facilities operating MistBuster®, Tri-Mist®, Trion®, Aerocology®, and Aeroex® air cleaners, where neglected maintenance and poor airflow design often reduce collection efficiency.

Together, these problems resulted in excessive smoke throughout the facility, creating poor indoor air quality that negatively impacted employee comfort, operational efficiency, and overall working conditions.

The Solution

Rather than recommending a costly replacement, Bee Clean Specialties completed a comprehensive analysis of the existing system and presented several cost-effective solutions.

The available options included:

  • Replacing the existing SmogHog® units with new double-pass SmogHog® systems.
  • Upgrading the existing units with double-pass filtration while redesigning the ductwork.
  • Maximizing the existing equipment by replacing and balancing the ductwork while adding airflow capacity where additional CFM was needed.

These same engineering principles can be applied to many electrostatic air filtration systems, including MistBuster®, Tri-Mist®, Trion®, Aerocology®, and Aeroex® equipment.

The manufacturer selected the third option, with a goal of improving indoor air quality by at least 80% while avoiding the cost of a complete system replacement.

The project included:

  • Replacing the majority of the existing ductwork with properly sized and balanced ductwork.
  • Adding additional air cleaning capacity to provide the CFM required to capture smoke effectively at every machine.
  • Optimizing the existing SmogHog® system instead of replacing it.

The entire project was completed for less than $250,000—less than 10% of the estimated $3 million replacement cost.

Results

Following the upgrades, the facility’s SmogHog® air filtration system began operating as intended. The project not only met the company’s goal of improving indoor air quality by 80%, but exceeded expectations while extending the life of the existing equipment.

By upgrading rather than replacing the system, the manufacturer saved millions of dollars in capital costs while creating a cleaner, healthier work environment for its employees.

More than two years later, Bee Clean Specialties continues to provide scheduled preventive maintenance on the facility’s SmogHog® system. Bee Clean also provides inspection, maintenance, repair, and upgrade services for MistBuster®, Tri-Mist®, Trion®, Aerocology®, and Aeroex® electrostatic air cleaners, helping manufacturers maximize equipment life and maintain excellent indoor air quality without unnecessary replacement costs.

This long-term partnership has allowed the manufacturer to maintain exceptional air quality while protecting its investment, and employees and visitors continue to notice the dramatic improvement in the facility’s working environment.The company knew improvements were necessary but was hesitant to replace the entire air filtration system. A sister facility with similar air quality issues had recently invested approximately $1.5 million in a completely new filtration system. Because this Cleveland facility operated significantly more cold heading machines, a comparable replacement was estimated to cost nearly $3 million.

The Challenge

After performing a complete system evaluation, Bee Clean Specialties identified several issues that were preventing the existing SmogHog® system from operating efficiently.

The primary problems included:

  • The electrostatic air cleaners had not been serviced on a regular maintenance schedule.
  • Much of the ductwork was improperly designed, undersized, and out of balance, restricting airflow throughout the system.
  • Several SmogHog® units were undersized for their applications and could not provide the CFM required to effectively capture smoke at the source.

These same issues are commonly found in facilities operating MistBuster®, Tri-Mist®, Trion®, Aerocology®, and Aeroex® air cleaners, where neglected maintenance and poor airflow design often reduce collection efficiency.

Together, these problems resulted in excessive smoke throughout the facility, creating poor indoor air quality that negatively impacted employee comfort, operational efficiency, and overall working conditions.

The Solution

Rather than recommending a costly replacement, Bee Clean Specialties completed a comprehensive analysis of the existing system and presented several cost-effective solutions.

The available options included:

  • Replacing the existing SmogHog® units with new double-pass SmogHog® systems.
  • Upgrading the existing units with double-pass filtration while redesigning the ductwork.
  • Maximizing the existing equipment by replacing and balancing the ductwork while adding airflow capacity where additional CFM was needed.

These same engineering principles can be applied to many electrostatic air filtration systems, including MistBuster®, Tri-Mist®, Trion®, Aerocology®, and Aeroex® equipment.

The manufacturer selected the third option, with a goal of improving indoor air quality by at least 80% while avoiding the cost of a complete system replacement.

The project included:

  • Replacing the majority of the existing ductwork with properly sized and balanced ductwork.
  • Adding additional air cleaning capacity to provide the CFM required to capture smoke effectively at every machine.
  • Optimizing the existing SmogHog® system instead of replacing it.

The entire project was completed for less than $250,000—less than 10% of the estimated $3 million replacement cost.

Results

Following the upgrades, the facility’s SmogHog® air filtration system began operating as intended. The project not only met the company’s goal of improving indoor air quality by 80%, but exceeded expectations while extending the life of the existing equipment.

By upgrading rather than replacing the system, the manufacturer saved millions of dollars in capital costs while creating a cleaner, healthier work environment for its employees.

More than two years later, Bee Clean Specialties continues to provide scheduled preventive maintenance on the facility’s SmogHog® system. Bee Clean also provides inspection, maintenance, repair, and upgrade services for MistBuster®, Tri-Mist®, Trion®, Aerocology®, and Aeroex® electrostatic air cleaners, helping manufacturers maximize equipment life and maintain excellent indoor air quality without unnecessary replacement costs.

This long-term partnership has allowed the manufacturer to maintain exceptional air quality while protecting its investment, and employees and visitors continue to notice the dramatic improvement in the facility’s working environment.

Share: